Velleman VTEMF

I wrote about EMF measurements and told that for magnetic field measurements I have used Velleman Magnetic Field Detector VTEMF. Velleman describes the product uses: “Detects the harmful electromagnetic fields generated by high voltage cables, computer and television screens, microwave ovens, waterbeds, electric blankets, etc.”.

That sounds reasonable. The description continues “Scientists believe that electromagnetic fields of 2-3mG and above, increase the risks of cancer and other dangerous disorders”, which is gives some numbers but it is hard to say based on recent research if those levels cause any problems or not.

Anyways being able to measure varying magnetic fields is useful, and this meter is much more more sensitive in that than my DIY magnetic field measurement adapter.

Here is the picture of the product:

mmit_DSCF1116

VTEMF Magnetic Field Detector User Manual says that VTEMF detects well the low-frequency fields (like caused by 50-60 Hz currents). The device had LED indication: 1, 3, 6 and 10mG (milliGauss) magnetic field strengths. In addition the meter has a beeper that makes sound when highest level LEDs are on. (If you want results in other units then think that 1 mG = 0.1 uT and 1 A/m = 12.6 mG).

When searching for information on VTEMF meter on Internet (I was looking for the manual and comments on meter), I found an interesting note on VTEMF: some ghost hunters use this meter and have rated it as good tool, although there is no evidence connects the use of EMF meters for ghost detection.

A look inside VTEMF meter:

min_DSCF1117

As you can see in the picture there is a large air cored coil that acts as the magnetic field detector (you need to aim it to point to the source to get best reading). Signal from coil is fed to amplifier, rectifier and display control circuitry. I have not reverse-engineered the measuring circuit inside meter, but I think it would resemble pretty much LED VU meter or similar device.

When I tested the meter with different magnetic fields, it seemed that it gave somewhat sensible measurement results (although without any accurately calibrated magnetic field or instrument to compare is hard to say anything on the absolute accuracy). I found some sources of EMI easily with it. I get the device beeping near wall-warts. I found magnetic field near mains distribution panel and some equipment. VMEMF also detects bass beats when put near bass speaker (light ups to few milliGauss flashing). I have also used VTEMF as a debug tools when trying to figure out why noise gets to some audio/video systems.

Besides detecting mains frequency fields, I have found that VTEMF also detects higher frequency fields up to few kHz with somewhat reduced sensitivity. I did tests with a coil connected to a signal generator to get idea of the frequency response. It also seemed detect (reduced sensitivity) also electronics tooth-bush chargers (operating at 10-22 kHz frequencies).

This VTEMF seems to be OK meter for measuring magnetic fields. The list prices I found this meter seems to be around 35-60 Euros depending where to buy it. I got mine years ago at much cheaper price.

8 Comments

  1. Tomi Engdahl says:

    Here are pointers to some DIY Electromagnetic field detector circuits:

    How to build Electromagnetic field detector
    http://www.circuit-finder.com/categories/sensor/magnetic-sensor/102/electromagnetic-field-detector

    Electromagnetic Field Probe with Meter Output
    http://www.diy-electronic-projects.com/p294-Electromagnetic-Field-Probe-with-Meter-Output

    Reply
  2. lurlempObbery says:

    An intriguing discussion is worth comment. I think which you really should write more on this topic, it might not be a taboo subject but frequently folks are not sufficient to speak on such topics. To the next. Cheers

    Reply
  3. Bettyann Chorlton says:

    Thanks, a very useful bit of information for all. Your thoughts on this subject are amazing and I am sure that these ideas will definitely apply to many other inviduals out there.

    Reply
  4. Fendi says:

    Interestingly citing the op’s article many will agree with the above since its true and its great reading from a person that’s showing this for all to read.

    Reply
  5. Smith Optics Knowledge Otg says:

    Obviously going through the op’s information I accept it as it’s what we really feel and it’s nifty to see a person thats writing it for us to look at

    Reply
  6. Frye says:

    Simply understanding this content I accept it since it is reality so its pleasant reading from a webmaster that’s posting content such as this for all to consider!

    Reply
  7. klicken Sie einfach auf die bis kommenden Artikel says:

    I have been surfing online more than 3 hours today, yet I never found any interesting article like yours.
    It’s pretty worth enough for me. In my view, if all web owners and bloggers made good content as you did,
    the web will be a lot more useful than ever before.

    Here is my web-site; klicken Sie einfach auf die bis kommenden Artikel

    Reply
  8. Tomi Engdahl says:

    EMF Meter – EMF Measurement – Basic Education: Using the Correct EMF Meter
    https://www.youtube.com/watch?v=B_G8wM7RhGQ

    This video is a basic introduction to using the correct EMF meter for what you want to measure. A basic, beginners explanation of which meter to use for magnetic and electric fields, dirty electricity (high frequency transients), radio frequency and microwave radiation, and for ionizing radiation.

    Reply

Leave a Comment

Your email address will not be published. Required fields are marked *

*

*