Replacing flashlight bulbs with LEDs

One day I had an old flashlight that had burned light bulb on it. It was a small cheap model powered with two AA batteries. I could fix it with new light bulb, but going through the trouble of trying to find exactly suitable replacement light bulb felt like more than the value of the flashlight.

If I need to replace the bulb with new one, why not convert the lamp to use LED instead.The lamp runs on two AA batteries in series. They give out around 3V voltage. That’s about the same voltage drop many white LEDs have (typically 2.8-3.5V or so). I had earlier found out that some white LEDs can be directly powered with 3V battery without any current limiting electronics. You just need to find out suitable LED. Some small LED lamps are driving white LED with 3V lithium button cells without a resistor! There are LEDs out there with internal resistors. And there are some LED that just work.

The general advice is that DO NOT use LEDS without a current limiting resistor in series with the LED. The forward voltage rating is TYPICAL and can vary from part to part, so while some LEDs may work fine just connected to a battery of the proper voltage, others will be easily over-driven and be destroyed.

Driving an LED with or without a resistor article on the other hand says that if you are able to run your complete circuit with the same voltage as forward voltage of the LED, perfect. No resistor needed. If you try to run run a 3.2 /3.4 volt warm white of a 3 volt power supply, you will get light but not the maximum amount. But usually enough for small flashlight application anyways. I had even used this idea on my LED light ring for macro photography project, so I was pretty comfortable with this idea.

Now all I need was to find suitable LED from my electronics junk box. I could check the datasheet or do measurements to verify suitability of the LED. It seemed that quite many white LEDs can be run from 3V battery without limiting resistor. But it is best to verify with measurement that things work well. I took a random white LED and put it to Kemo M087 LED testing box. I tested the voltage drop of the LED and different currents from 5 mA to 20 mA (and very quicly with 50 mA). The LED seemed to take somewhat less than 3V at 5 mA and 10 mA. At 20 mA the voltage drop was around 3.2V. At 50 mA the voltage drop was around 3.4V. With this data I could expect that with two new AA batteries in series (gives around 1.6V each) the LED would take around 20 mA current and the current would drop from that when batteries wear out. With this data it seems that this LED would work here.

The next step was just building the LED bulb replacement. Here is a small DIY flashlight bulb LED replacement. It consists of the lamp base (small edison base from old broken bulb), 5mm white LED, solder tin and hot glue. The LED anode goes to the center of the light bulb base.

ledbulb

Here is picture of my LED bulb in the flashlight in use.

ledlamp

Now I have a nice working flashlight that is not very bright, but that has a very long battery life.

If this modification looks interesting, then you might wonder how to convert lamps with different number of batteries to LED lamps. With flashlights that use three batteries or mode, the standard method to use would a white LED + suitable current limiting electronics does job. A resistor will work nut switch mode current source is better. For 20 mA LED and 4.5V operation voltage a 75 ohms or 82 ohms resistor will do. For other operating voltages and LED currents, do your own LED resistor calculations.

If your flashlight uses just one 1.5V battery, you will need a switch mode power supply that boosts the battery voltage to over 3V and limits the current. Joule Thief is a nickname for a minimalist self-oscillating voltage booster that is small, low-cost, and easy-to-build. It can use nearly all of the energy in an electric battery, even far below the voltage where other circuits consider the battery fully discharged (or “dead”). The energy is converter to current and voltage suitable for driving white LED. Make a joule thief if you want to drive white LED from one 1.5V battery.

12 Comments

  1. gaucho says:

    Of program like your web site but you need to have to test the spelling on many of your posts. Many of them are rife with spelling troubles and I uncover it genuinely bothersome to tell the fact however I’ll surely occur back again once once again.

    Reply
    • Gess X says:

      Huh? What’d you say??? Something about spelling, and it needing testing. Maybe it does. Maybe it doesn’t. One thing is for certain. That being before trying to correct others of their works, written in English, you should learn English yourself. Your statements are difficult, at best, to follow, much less read them in a smooth flowing manner. Perhaps your post is translated. If so the translator needs to learn English.

      “Spelling troubles”, would normally be used to indicate someone having trouble spelling. When addressing someone having an article with misspelled words, one would use ‘misspelled’, ‘spelling errors’, or ‘spelling mistakes’, something similar.

      “…and I uncover it genuinely bothersome …” Uncover is something one does with a tarp, lid, or a blanket. They uncover it. ‘Uncover’ is not a substitute for ‘find’. You find it ‘really’ bothersome, or ‘rather’ bothersome, but not ‘genuinely’ bothersome

      There’s more but that’s a start anyway. Correct or critiquing someone about their spelling is not a place you should be going. At least not until you become more proficient in the language. Have a good day.

      Reply
  2. Laronda Woliver says:

    Interesting but I am not sure if I agree with it.

    Reply
  3. Mario says:

    Interesting use of the LEDs

    Reply
  4. Tomi Engdahl says:

    Gadget Freak Case #228: Super LED Flashlight Hits 3,000 Lumens
    http://www.designnews.com/author.asp?section_id=1362&doc_id=251425&cid=NL_Newsletters+-+DN+Daily

    Fifteen-year-old Gadget Freak John Duffy has put together a powerful LED flashlight.

    Duffy’s super LED flashlight runs at almost 30W and 3,000 lumens. By comparison, bright xenon car headlights reach about 1,000 lumens. He says you have to be careful building and using this gadget, because it is powerful enough to blind someone if used up close. He used welding glasses while constructing the flashlight.

    Reply
  5. aneurysm behind knee says:

    There are actually plenty of particulars like that to take into consideration. That could be a nice level to carry up. I supply the ideas above as basic inspiration but clearly there are questions just like the one you convey up the place the most important factor will likely be working in honest good faith. I don?t know if greatest practices have emerged around things like that, but I am certain that your job is clearly recognized as a good game. Both girls and boys feel the affect of only a second’s pleasure, for the remainder of their lives.

    Reply
  6. Raymon Tokita says:

    Great – I should certainly pronounce, impressed with your site. I had no trouble navigating through all tabs as well as related information ended up being truly simple to do to access. I recently found what I hoped for before you know it in the least. Quite unusual. Is likely to appreciate it for those who add forums or anything, website theme . a tones way for your client to communicate. Nice task..

    Reply
  7. Levi says:

    Simply wish to say your article is as surprising.
    The clarity for your put up is simply nice and i could think you’re an expert on this
    subject. Well along with your permission let me to
    snatch your RSS feed to stay updated with approaching post.

    Thanks a million and please keep up the enjoyable work.
    Levi

    Reply
  8. 911 says:

    Great use of LEDs Wonderful

    Reply
  9. LED Flashers says:

    I found some amazing LED flashers on this website owned by 911 Custom.

    Reply

Leave a Comment

Your email address will not be published. Required fields are marked *

*

*