Electrolytic capacitor failures

The most common reasons that modern digital electronics devices fail seem to be a bad electrolytic capacitors. Bad electrolytic capacitors cause frequent failures of switch mode power supplies. It seems power supplies are often the weakest link in many modern electronics devices.

Since there is tremendous price pressure on PC’s and other consumer electronics devices, there is great pressure for a low-cost power supply, which often means several things. Low-cost components with limited life are often used, circuit components that might limit secondary failures are left out, and parts are often used at or beyond their ratings, causing poor reliability and short life.

The weakest link in power supply is usually one of the electrolytic capacitors. Usually electronics repair people need to replace more electrolytic capacitors than any other electronic components in electronic repair. The aluminum electrolytic capacitor has a limited life span. This occurs because the electrolyte in the element eventually dissipates. Since electrolytic capacitors are not hermetically sealed, the electrolyte in these capacitor eventually evaporates causing increased ESR which causes increased heating, which causes the safety seal on the capacitor to pop, because if it does not pop, the capacitor explodes. Once these capacitors fail, they can cause all kinds of secondary failures. Why this kind of often failing components are then used? By combining small size and very low cost per unit capacitance, electrolytic capacitors are the only cost-effective choice for high-value applications like power supply filtering in most consumer gear.

The changes in performance over time can be described as follows: Eventually, the capacitance begins to drop off and internal resistance (ESR) starts to increase. The loss in capacitor begins to increase, causing it to heat up more and go bad more quickly. Finally, at the end of the life span, the capacitor enters an open circuit mode as the dielectric dries up. More details can be found at Reliabity of Aluminum Elecrolytic Capacitors document.

The capacitor plague involved the common premature failure of certain brands of electrolytic capacitors used in various electronics equipment, and particularly in motherboards, video cards, compact fluorescent lamp ballasts, LCD monitors, and power supplies of personal computers. The first flawed capacitors were seen in 1999, some bad capacitors were still being sold or integrated into designs as of early 2007. An incorrect electrolyte formula within a faulty capacitor causes the production of hydrogen gas, leading to bulging or deformation of the capacitor’s case, and eventual venting of the electrolyte.

image004

A serious quality control problem is that good and poor quality electrolytic capacitors will often have identical electrical performance when newly fitted. But when the bad capacitors are stressed for a long time with high ripple current in hot environment, their electrical performance changes considerably causing the common premature failure. Most other electronic components which are much less subject to spontaneous failure after assembly.

Criteria for Defining Failures in Aluminum Dielectric Capacitors could be something like this:
1. Considerable changes in capacitance is noticed. A failure is defined as a change in capacitance from the initial capacitance level beyond the specified range. The change is generally ±20% to ±30%.
2. Change in Equivalent Series Resistance (ESR). A failure is defined as the component exceeding the specified range. Usually, this range is 1.5 to 3.0 times the initial value.
3. Change in leakage current. The definition of failure occurs when there is an excess of the specification values.

As you can see measuring the capacitance with a multimeter with capacitance meter functionality does not tell the whole story. It is wise to invest on ESR meter which can test e-caps in or off board. If you like building electronics circuits, you can make your own ESR meter based on An Equivalent Series Resistance Meter plans you can find at http://www.ludens.cl/Electron/esr/esr.html. I have successfully built this circuit and I can tell it works well.

Replacing and reforming electrolytic capacitors was quite common before the current throw-away culture took hold. Some people and companies still repair and replace electrolytic capacitors, but usually it is cheaper to throw broken electronics away than it is to perform preventive maintenance or repair it. To pick electronics that last, look for products that have the longest warranties. Since it is VERY expensive for manufacturers to repair computers and other electronics under warranty, they usually pick parts and de-rating to make sure their product lasts at least as long as the warranty.

Before designing electronics that uses electrolytic capacitors, read Application Guide, Aluminum Electrolytic Capacitors to know how to use them correctly.

60 Comments

  1. Tomi Engdahl says:

    Six Common Mistakes Made When Recapping Vintage Electronics
    https://www.youtube.com/watch?v=BeDKwi-GJRI

    Short little video on common mistakes seen when recapping (replacing capacitors) vintage electronics. This would include vintage stereos, radios, equipment, CBs, ham radio receivers & transmitters, calculators, computers, you name it.
    Hopefully this will provide you some tips and hints to use when you go to recap your piece of vintage gear.
    Topics include:
    - Mistaking Factory Glue for Leaking Capacitors
    - Factory Boards and Manuals Marked Wrong
    - Capacitors Installed Incorrectly
    - Using Larger Capacitors Than Specified
    - Buying Electrolytic Capacitors off Ebay
    - Replacing Everything at Once

    Reply
  2. Tomi Engdahl says:

    SMPS repair:

    First – cleaning.
    Second – recap.
    Third – diodes.
    Fourth – the output transformer.
    And then … imagine.

    Reply
  3. Tomi Engdahl says:

    Electrolytic Capacitors: Comprehensive Overview, Teardown, and Experiments
    https://www.youtube.com/watch?v=MAP-VA1m-A4

    Through experiments, I compared different types of electrolytic capacitors such as solid and hybrid.

    0:00 Brand Name Changes to Chemi-Con!
    0:33 Which Products Use Eleltrolytic Capacitors?
    2:26Difference Between 3 Types of Aluminum Electrolytic Capacitors
    3:04Type 1: “Commonly Used” Aluminum Electrolytic Capacitor
    4:34 Structure and Equivalent Circuit of an Aluminum Electrolytic Capacitor
    5:40Type 2: “Low ESR” Conductive Polymer Aluminum Solid Electrolytic Capacitor
    6:45 Type 3: “Get the Best of Both Worlds” Conductive Polymer Hybrid Aluminum Electrolytic Capacitor
    7:16 ESR (Equivalent Series Resistance) of Electrolytic Capacitors
    8:49 Lifetime of Electrolytic Capacitors
    10:09 Same Capacitance, Different Ripple Voltages
    12:19 Reverse Polarity (*Do Not Try This Yourself*)
    13:26 Operating Temperatures of Electrolytic Capacitors

    Reply
  4. tomi says:

    Lots of spam is slowly starting to driving me mad.. over 100 spams every day…
    Does anyone know any good plugins or such to help this?
    On thing I use is configuration that makes the comments only visible after they have been accepted…
    So the spams typically get filtered out in the moderation process.. but it takes time to filter out those few real comments from over 100 spams…

    Reply
  5. tomi says:

    Thank you for yiur feedback. The amount of spam has increased a lot lately and I start hating dealing with this every day. I have no good solution for that yet.

    Reply

Leave a Comment

Your email address will not be published. Required fields are marked *

*

*